Cm2 Box install CM2MT2 v2.00-R4 Setup File

FREE

InfinityBox install CM2MT2 v2.00-R4 Module is Ready to Download.After Long time Infinity Team updates there cm2 MTK Dongle. Download InfinityBox install CM2MT2 v2.00-R4 from below link and enjoy. Remember ! This file work with Dongle only it’s not Crack .

InfinityBox install CM2MT2 v2.00-r4 Setup Download

CM2MT2 v2.00-R4

Whats New On InfinityBox install CM2MT2 v2.00-R4 ? 

≡ Main
⇒ Connection level revised
⇒ BROM level support optimized

MT6771 CPU supported!
⇒MT6771 moved from TEST to GENERAL support.
⇒Firmwware read
⇒Firmware write
⇒NVRAM read
⇒NVRAM write
⇒Reset Settings / Format FS
⇒Reset FRP
⇒Reset Privacy
⇒MemoryTool

≡ Service
⇒ Repair Security revised. Fixed issues with some NV types.

≡ Core
⇒ EMIDB updated
⇒ Hint/Error explain module updated
⇒ MT6758 support under test
⇒ MT6765 support under test

≡ FW reader
⇒ MT6771 supported
⇒ New types of firmwares supported
⇒ Scatter creation optimized

≡ SP Unlock
⇒ Revised unlock support for some models
⇒ Info: MT6739/MT6763/MT6771 IS NOT supported YET!

≡ New models included
⇒ Limited Oppo support (F7/A3)
⇒ Limited Vivo support
⇒ And diffirent other models
⇒ Some other basic “generic” secure devices support optimized

Known issues/warnings/info:
1. [NAND on MT6570] v1712, v1736 loader packages SHOULD NOT BE USED due to these packages have ftl/ecc errors!
In result you will give read/write FW errors and rest problems at all.
Recommend use v1724 for FACTORY FW flashing, v18xx line for Infinity FW Flash Read and Write
2. [NAND on MT6570] In some cases “stuck on logo” devices can be fixed only via FFU (whole flash) format!
3. [MEMORY TOOL] Partitions state on MEMORY TOOL will be empty in MT6570 NAND phones, it is normal behaviour and can not be fixed.
Read-Write data, which you want, ignore “EMPTY” states.
4. ADL checksum MAY NOT WORK CORRECT on MT6570 NAND devices! Result – stuck after system/userdata partition flashing
5. FileSystem flashing on some SBC-enabled devices ( except SYSTEM/CACHE/USER ) may fail! Solution – exclude them from flashing list.
6. Cheap MT6739 devices require BATTERY REMOVING after EVERY operation in most cases!
7. Meizu support is limited by Preloader Level ( No BROM SLA ) – you must UNTICK “PMT Update” and “PRELOADER” partition from flashing list!
8. [NAND on MT6570] In some cases device MAY DEAD after flashing! Make sure you have TESTED firmware version!
If you have download FW from internet/other source – make sure it preloader CONTAIN 3 EMI record! Preloader jc45btlc with 2 records KILL SOME DEVICE TO UNRECOVERABLE STATE!!!
Preloader info shown now during FW load.

Credits :
kamal_singla – testing and useful files contribution

Important:
– Software installed to new folder /CM2MT2/ and designed to support new models
– Smart-Card firmware v0136 is Ok to use this version
– DO NOT uninstall previous version 1.58 ! If you are trying to connect phone with new software and see a message like LEGACY MTK you should use version 1.58 for this device !

Download InfinityBox install CM2MT2 V2.00-R4 Setup

Download Setup File